[SIZE=5][FONT=Arial][B]自从买了佛洛伊德双摇琴,调弦就一直困扰着我.终于找到了一篇详细的教程.[/B][/FONT][/SIZE]
[SIZE=5][FONT=Arial][/FONT][/SIZE]
[SIZE=5][FONT=Arial][/FONT][/SIZE]
[SIZE=5][FONT=Arial][B]FLOYD ROSE BRIDGE SECRETS[/B] [/FONT][/SIZE][FONT=arial][SIZE=2][COLOR=#000000]
A guide to help you save time and frustration!

Developed in the early 80’s, the Floyd Rose bridge design allows guitarists who want to use their tremolo bar (aka the “whammy bar”) but have their guitar remain in tune. Older designs like the original Fender Stratocaster bridge simply don’t stay in tune well when the tremolo bar is used, especially when it’s used for “dive bombs”- extreme slackening of the strings.
Our guide is designed to help the novice and experienced guitarist alike in restringing the typical Floyd Rose design as found on many of today’s popular guitars such as those by Ibanez, Jackson, Squier, and others. Restringing a Floyd Rose can be a time consuming and sometimes frustrating process. These simple tips will help you change strings faster and with fewer hassles! Please note that a quality electronic guitar tuner is essential for this task.
Before doing anything else, with your guitar in tune, look at the bridge from the side. Is it floating parallel to the face of the guitar like the one pictured below?
[IMG]http://www.musicstop.com/images/tips2_a.gif[/IMG]
If so, you are ready to proceed. If not, skip to the section of this guide on setting spring tension then come back.
Note that if you are not comfortable making these adjustments to your guitar we recommend taking it to a qualified guitar repairperson.
The next step is to find something to block the bridge so that it doesn’t move while changing the strings. A 9 volt battery wrapped in electrical tape or one of those pink pencil erasers works well. The object you use should tilt the bridge forward very slightly- just enough to keep the object in place.
Once you’ve found an object to block the strings with we begin the process of replacing the strings. This should be done one string at a time. First, unlock the locking nut for each pair of strings. Set the fine tuner for each string in the middle of its range of adjustment.
Detune the high ‘E’ string using the tuning machine on the headstock. Once the string is detuned, unlock it from the bridge saddle by loosening the corresponding screw at the back of the saddle. Remove the string from the guitar.
Next, clip the ball end off the new string with a pair of string cutter or wire cutters and lock it into the bridge saddle. Be sure to tighten the screw at the back of the saddle so that it’s snug but you do not need to over tighten.
Now, tune the string using the tuning machine on the headstock. The next step is VERY IMPORTANT. You must stretch out the string very well by holding it down at the 5th fret, tugging firmly on it above the 12th fret and then retuning until you reach a point where tugging on the string doesn’t make the string go flat. Once the string has been stretched out, make sure it is in tune and then repeat the whole process for the each string one at a time. Detuning, removing, replacing and stretching each string in turn.
Once all the strings have been replaced, remove the object blocking the bridge. You’ll notice that all of your strings are now slightly sharp. Starting with the high ‘E’ and working your way up to the low ‘E’, tune each string using the tuning machine on the headstock. Repeat, starting with the high ‘E’ each time until all the strings are in tune and the bridge is once again floating parallel to the face of the guitar as pictured above.
Finally, lock the locking nut (it should be snug but don’t over tighten). Fine tune the guitar using the fine tuners on the bridge. Plug in, turn up your amp and play!
[B]SETTING SPRING TENSION[/B]
Trying to tune your Floyd Rose equipped guitar and having your bridge tilt forward or back? This is a sign that your tremolo springs are not correctly adjusted to counterbalance the tension of the strings. This could be due to changing your string gauge and not adjusting the trem springs to compensate or using non standard tunings (drop ‘D’ or tuning down).
Adjusting the tremolo springs so that the tremolo floats parallel to the top of the guitar (see diagram on other side) is fairly straight forward. If the bridge is tilting forward towards the neck of the guitar, there is not enough tension and the springs need to be tightened or in some cases an extra spring added. If the bridge is tilting back the spring tension is to great and needs to be loosed or a spring removed.
Generally, players using .008-.010 strings should use 3 (or sometimes 2) springs, players using heavier strings may need to use an additional spring.
If your tremolo is leaning forward, unlock the locknut nut and loosen your strings using the tuners on the headstock. Next, tighten the two screws which hold the spring claw into the body.
[IMG]http://www.musicstop.com/images/tips2_b.gif[/IMG]
A small adjustment may be all that is necessary, begin with a half turn on each screw using a Philips screwdriver. After adjusting the claw, retune the guitar (using an electronic tuner) and check the bridge. If it is still leaning forward you will need to repeat the steps again.
If the screws are all the way into the body and the bridge is still tilting forward you will need to add an extra spring. Some guitars come with a spare spring, if not you can purchase one at your local Musicstop, they are very inexpensive.
If the bridge is tilting back you will need to loosen the screws, begin with a small adjustment- a quarter or a half turn. Repeat as necessary. It may also be necessary to remove one of the springs in order to lessen the tension. Once you can tune the strings to the desired pitch and the bridge will float level you’re done!
[/COLOR][/SIZE][/FONT]

佛洛伊德不是大夫吗，怎么改卖琴了？:eek: :wink:

哈哈，你说的是弗洛伊彪吧。

[quote name='nolimited']哈哈，你说的是弗洛伊彪吧。[/QUOTE]

嘿嘿,这可是你说的.

我说呢，昨敢情为了琢磨这个啊~

[quote name='铃音']我说呢，昨敢情为了琢磨这个啊~[/quote]


:biggrin: :biggrin: :biggrin: :biggrin: :biggrin: 那是。。。没在你家吃饭主要是心急回家调琴。。。

以后实行"三包"政策，包吃，包玩，包住。 .跳楼价:每人50刀/day

包吃，包玩儿可以理解，怎么包住听听。。。

[quote name='nolimited']包吃，包玩儿可以理解，怎么包住听听。。。[/QUOTE]

我们家有三朵金花: 小津(小娇)，小马(睡美人)，肉肉(受虐无极限)
你挑吧，看你喜欢乃类型的

[quote name='铃音']我们家有三朵金花: 小津(小娇)，小马(睡美人)，肉肉(受虐无极限)
你挑吧，看你喜欢乃类型的[/quote]

我能加入吗?

[quote name='nolimited']我能加入吗?[/quote]

我看成:biggrin:


[COLOR=red][quote name='nolimited'];改我帖子？？？版主了不起啊？？？欺负人。。。555~~~[/quote][/COLOR]

欺负人，改我帖子。。。

[img]http://image.ibox.com.cn/bbsupimage/uploadimage/messageimages/cartoon/2005-6-7/1118186073.gif[/img]

[quote name='nolimited']欺负人，改我帖子。。。[/QUOTE]

认命吧，现在是女人当道啊:frown:

调制Floyd Rose琴桥系统
版权归属：Floyd Rose
[url]http://www.gibraltarlivemusic.com/tech/1056116567-Setting%20Up%20a%20Floyd%20Rose%20Equipped%20Guitar.doc[/url]
翻译：无名之琴
换弦：
1． 松开琴枕部位的3个估定琴弦的锣母
2． 把琴桥上的旋钮（fine-tuners）拧到中间的部位
3． 每次换一跟弦，先把现放松，在把琴桥后面长的估定钉放松
4． 把弦上带球的一端减掉
5． 把新减断的一端插到琴桥的的槽力，拧紧长的估定钉，紧的再拧不动最好
6． 把弦的另一端接到琴头联好
7． 重复2到5的步骤直到所有的弦都换了
8． 检查一下6根弦的音准
9． 把琴枕的3个估定螺母拧紧
10．再查一遍音准，这次用琴桥上面的小旋钮调
调试琴桥：
这是俘动琴桥很关键的一关。我们的理想是找到在琴弦和在琴被后的3跟弹簧之间拉力的平衡点。
1． 同上1
2． 同上2
3． 把你的琴调到你希望的音
4． 在你调完所有的弦后，查一下6弦E（最粗）的音，如果现在6弦成了Eb，从新再把6根弦都调一遍，不过这一次要把每一个音都调的稍高一点。假如6弦是稍高，则把其他5弦都调的稍低一点。原因是，每次你调音，都多少改变了两边（弦和弹簧）的拉力，1根弦松了，会导至其他弦的音也被改变了
5． 重复4直到所有的弦都准了
6． 这时再看琴桥的底盘是不是和琴体表面处于平行的水平上。如果琴桥稍像前倾，说明弦的拉力大于弹簧的拉力，这时你要调弹簧，方法是打开琴底的盖，有两的螺丝钉一边查在琴身里，另一边挂着一个小耙子，弹簧就挂在这个耙子上，你要做的是把两个螺丝钉往琴身里拧，这样弹簧就被拉的更开，拉力也更大。如果琴桥是像后面倾，说明弹簧拉力大过弦，这时你要送开2个螺丝钉一些，直到琴桥处于完全水平
7． 如果上面都做好了，就可以把琴枕的3个估定螺母拧紧了
8． 调音完毕，现在再看琴弦的高度，或高或低则由起估定亲桥作用的两个钉子决定，调高度会稍稍跑点调
调音准：
1． 用音叉或表准设备保怔调音的准性，送开琴枕的螺母
2． 看一个亲的音准，就是通过人工泛音的方法，把手指轻轻的放到每根弦的12品上在弹，在按在12品上弹，看两者的声音是否像同。 如果按下去弹的音稍低，则要把在琴桥上估定这根弦的单位像前移，直到12品音和泛音相同为止。如果按品弹的比泛音高，则要把估定这根弦的单位像反方向移。
如果你的琴装备的是原装Floyd Rose琴桥，在正确的调试下应该是非常好的，下面是一些事要，看是没有调好还是琴桥本身有损：
1． 看琴桥底盘是否水平（看上）
2． 看整个琴枕是不是在琴颈上卡的死死的
3． 琴枕的螺母和琴桥的长估定钉是否卡死
4． 音准是否调好
如果以上都做好了，但你的琴桥还是总跑音，说明很可能琴桥上的刀片部位有损了，为了近一步确认，你要将正个琴桥歇下（翻者语：得，白干了），看刀片部位是生锈了还是有缺口了
如果刀片部位不再锋力，可以想办法单买一个底盘
在所有的问题中，刀片生钝是很少发生的，由其是真正的Floyd Rose，但在那些授权生产的Floyd Rose比教常见。